WJX-16高速乳膠機械穩定性測定儀

功能、適用范圍:

    高速乳膠機械穩定性測定儀主要適用于膠乳生產單位和科研院所對天然膠乳和合成膠乳做機械穩定性測試，是提高膠乳質量必不可少的儀器。

采用電機后備容量大，選用高可靠性，大扭矩的高速電機，速度控制系統可實時根據電機負載變化調整電機轉速，轉速準確平穩，轉速可調。

執行標準：ISO2006的標準要求《GBT 8301-2008 濃縮天然膠乳 機械穩定度的測定》和《SHT 1151-1998 合成膠乳高速機械穩定性的測定法》標準要求

主要技術參數：

1)使用條件：溫度10℃～40℃ 、濕度<85%RH；

2)攪拌轉速：14000rpm±200rpm；

3)示值誤差：≤0.1%；

4)測量分辯率：1rpm；

5)顯示方式： LED顯示；

7)**轉速：20000rpm；**轉速：2000rpm；

8)體積：400mm×350mm×720mm；

9)凈重：約30Kg；

10)攪拌圓盤的規格：

天然膠乳：直徑20.83±0.03mm 厚1.57±0.05mm

合成膠乳：直徑36.12±0.03mm 厚1.58±0.05mm

11)膠乳容器：高130±2mm，內徑58±2mm

12)能夠連續運轉1小時.

13）儀器尺寸：400mm×350mm×740mm

14）所需空間：前后0.5m，左右1.0m

15) 電源：2000VA   220VAC   50HZ

結構及工作原理：

調速部分采用了先進的變頻調速控制模式，運用負反饋技術，能夠精確的進行轉速的控制，寬范圍的滿足對轉速的設定和調節，并且具有多種顯示方式，可以直接顯示轉速。

攪拌圓盤與攪拌軸過盈配合，壓緊組裝，保證了攪拌圓盤和轉動軸同心，電機經過動平衡試驗保證了電機在14000rpm的情況下，軸的擺動不A大于0.25mm。

膠乳容器采用柔性連接方式和托架進行連接，膠乳容器固定用杯托升起或落下，限位套沿立柱方向的固定位置決定膠乳容器底部距攪拌圓盤底部的距離，本儀器位置已調好，用戶不需調整限位套的位置。

儀器整體重心穩固，支撐牢固，不易變形，容器的定位靠上定位塊實現。

Wjx-16 high speed latex mechanical stability tester

Function and scope of application:

High-speed latex mechanical stability tester is mainly used in the latex production units and scientific research institutes to natural rubber latex and synthetic latex mechanical stability tests, instruments are essential to improve the quality of latex.

The motor reserve capacity is large, using high reliability, large torque of the motor, speed control system can real-time according to adjust the motor speed, motor load change speed is accurate, smooth and adjustable speed.

Implementation standard: meet ISO 35 standard requirements

Main technical parameters:

1) use conditions: temperature 10 ℃ to 40 ℃, humidity < 85% RH;

2) stirring speed: 14000rpm plus or minus 200rpm;

3) indication error: less than or equal to 0.1%;

4) measurement resolution: 1rpm;

5) display mode: LED display;

7) maximum speed: 20000rpm;

Minimum speed: 2000rpm;

8) volume: 400mm x 350mm x 720mm;

9) net weight: about 30Kg;

10) specification of mixing disc:

Natural latex: diameter 20.83 plus or minus 0.03mm thick 1.57 plus or minus 0.05mm

Synthetic latex: diameter 36.12 + 0.03mm thick 1.58 + 0.05mm

11) latex containers: high 130 plus or minus 2mm, inner diameter 58, plus or minus 2mm

12) capable of running continuously for 1 hour.

13) instrument size: 400mm x 350mm x 740mm

14) required space: 0.5m before and after, 1.0m for left and right

15) power supply: 2000VA 220VAC 50HZ

Structure and working principle:

Speed control part adopts advanced frequency control of motor speed control mode, the use of negative feedback technology, can accurate speed control, the fulfillment of wide range of speed setting and adjustment, and has a variety of display mode, can be directly display speed.

Mixing disc and the interference fit for the stirring shaft, clamp assembly, to ensure the concentric mixing disc and the rotation axis, the motor through dynamic balance test to ensure the motor in the case of A 14000 RPM, the motion of the shaft is not A greater than 0.25 mm.

Latex vessel adopts flexible connection way and bracket to connect, latex vessel and fixed with a cup of Joe rise or fall, limit set along the direction of the post of latex fixed position at the bottom of the container from mixing disc at the bottom of the distance, the instrument has adjusted the location, users do not need to adjust the position of the limit set.

The overall center of the instrument is stable, the support is strong, not easy to deform, the positioning of the container is realized by the positioning block.